IIT Kanpur · Engineering

Fundamentals of Casting and Solidification

Prof. Virkeshwar Kumar · 60 free video lectures

This course, Fundamentals of Casting and Solidification, offers an in-depth understanding of the principles governing metal casting processes, from melt flow and heat transfer to solidification dynamics. It integrates heat, mass, and fluid flow analysis with the study of microstructural evolution…

▶ Play on Open Lecture HallCourse page ↗

Lectures

  1. Lecture 01: Introduction of the Casting Process
  2. Lecture 02: Types of molds and Casting Process
  3. Lecture 03: Patterns
  4. Lecture 04: Patterns Allowances
  5. Lecture 05: Patterns Allowances 2
  6. Lecture 06: Core Design
  7. Lecture 07: Pouring System
  8. Lecture 08: Vertical Gating System
  9. Lecture 09: Bottom Gating System
  10. Lecture 10 : Aspiration Effect
  11. Lecture 11: Effect of Friction and Velocity Distribution
  12. Lecture 12: Gating Design Modification
  13. Lecture 13: Basic Heat Transfer in Casting
  14. Lecture 14: Heat Transfer
  15. Lecture 15: Similarity Transformation Method
  16. Lecture 16: Solidification Time
  17. Lecture 17: Chvorinov's rule
  18. Lecture 18: Chvorinov's rule- 2
  19. Lecture 19: Solidification time for a non-flat surface in sand casting
  20. Lecture 20: Permanent mold casting: Solidification Time
  21. Lecture 21:Energy Balance at Interface
  22. Lecture 22:Energy Balance at Interface- 2
  23. Lecture 23: Steady- State Solidification: Bridgman method
  24. Lecture 24: Solidification of Supercooled Liquid
  25. Lecture 25: Stefan Number
  26. Lecture 26 : Solidification: Two-Phase Problem
  27. Lecture 27 : Solidification by Line Heat Sink
  28. Lecture 28 : Solidification in Superheated Melt
  29. Lecture 29 : Solidification in Superheated Melt- 2
  30. Lecture 30 : Solidification in Superheated Melt- 3
  31. Lecture 31: Thermodynamics For Casting
  32. Lecture 32 : Single Component System
  33. Lecture 33 : Effect of Temperature and Pressure
  34. Lecture 34 : Homogeneous Nucleation
  35. Lecture 35 : Homogeneous Nucleation- 2
  36. Lecture 36 : Heterogeneous Nucleation
  37. Lecture 37 : Heterogeneous Nucleation - 2
  38. Lecture 38 : Thermal Dendrites
  39. Lecture 39 : Binary Solution
  40. Lecture 40 : Binary Phase Diagram
  41. Lecture 41 : Lever Rule
  42. Lecture 42 : Lever Rule- 2
  43. Lecture 43 : Microstructure: Lever Rule
  44. Lecture 44 : Scheil Equation
  45. Lecture 45 : Segregation Profile
  46. Lecture 46 : Constitutional Undercooling
  47. Lecture 47 : Microstructure in Casting
  48. Lecture 48 : Microstructure in Casting- 2
  49. Lecture 49 : Solidification Time for Binary Solution- 1
  50. Lecture 50 : Solidification Time for Binary Solution- 2
  51. Lecture 51 : Convection in Pure Material Casting
  52. Lecture 52 : Convection in Binary Material Casting
  53. Lecture 53 : Convection in Casting
  54. Lecture 54 : Riser
  55. Lecture 55 : Riser Design
  56. Lecture 56 : Riser Design - 2
  57. Lecture 57 : Riser Design - 3
  58. Lecture 58 : Riser Design - 4
  59. Lecture 59 : Riser Design- 5
  60. Lecture 60 : Defects in Castings and Quality Control

From NPTEL (IITs and IISc) · CC BY-NC-SA. More from IIT Kanpur.

Open Lecture Hall is free, with no ads and no sign-up. It is not run by or connected to any university; the lectures are the universities' own free recordings, played from where they host them. About & rights