IIT Kharagpur · Engineering

Gear and Gear Unit Design : Theory and Practice

Prof. Rathindranath Maiti · 48 free video lectures

48 video lectures. Topics: Introduction- Motivation and Theme of the Course; Laws of Gearing, Kinematics and Geometry Part-I; Laws of Gearing, Kinematics and Geometry Part-II; Involute Toothed Gear- Properties & Terminology; Tutorial; Involute Straight Tooth Spur Gear; Helical Tooth Spur Gear &…

▶ Play on Open Lecture HallCourse page ↗

Lectures

  1. Lecture 1: Introduction- Motivation and Theme of the Course
  2. Lecture 2 : Laws of Gearing, Kinematics and Geometry Part-I
  3. Lecture 3 : Laws of Gearing, Kinematics and Geometry Part-II
  4. Lecture 4 : Involute Toothed Gear- Properties & Terminology
  5. Lecture 5 : Tutorial
  6. LECTURE 6: Involute Straight Tooth Spur Gear
  7. LECTURE 7: Helical Tooth Spur Gear & Loads on Gear Shaft
  8. LECTURE 8: Design of Bevel Gear
  9. LECTURE 9: Crossed Helical Gear-I
  10. LECTURE 10: Crossed Helical Gear-II and Worm Gear
  11. LECTURE 11 : Gear Unit Design - Selection of Stage Ratios, Pinion & Gear Teeth Numbers
  12. LECTURE 12 : Gear Unit Design - First Stage Pinion & Gear Design- I (Module on Beam Strength Basis)
  13. LECTURE 13 Gear Unit Design - Failure of Gear Tooth (Probable Dynamic Load and Wear Load Capacity)
  14. LECTURE 14 Gear Unit Design - 1st. Stage Pinion & Gear Design-II (Probable Dynamic Load and Wear Load Capacity and Finalizing 1st. Stage Pi…
  15. LECTURE 15 Gear Unit Design - 1st. Layout (After Gear Design)
  16. LECTURE 16 Bearing Arrangement-Gear Box Shafts
  17. LECTURE 17: Bearing Load Calculation- Intermediate Shaft
  18. LECTURE 18 Bearing Selection & Introduction to Shaft Design Verification
  19. LECTURE 19 Design Verification of Gear Box Shafts
  20. LECTURE 20 Development (Layout) of Intermediate Shaft
  21. LECTURE 21 : Development (Layout) of Input Shaft & Integral Pinion
  22. LECTURE 22 : Development (Layout) of Output Shaft and 2nd. Stage (Output) Gear
  23. LECTURE 23 : Development (Layout) of Output Shaft (contd.), Loads on Shaft & Bearings
  24. LECTURE 24 : Output Shaft-Bearing Lives
  25. LECTURE 25 : Design Verification of Output Shaft
  26. LECTURE 26 : Design Verification of Input Shaft (including Bearing Life Estimation)
  27. LECTURE 27 : Finalizing Design including the Sizes of the Keys
  28. LECTURE 28 : Development of Plan & Elevation of Gear Reduction Unit- I
  29. LECTURE 29 : Development of Plan & Elevation of Gear Reduction Unit- II
  30. LECTURE 30 : Development of Plan & Elevation of Gear Reduction Unit- III
  31. Lecture 31 :
  32. Lecture 32 :
  33. LECTURE 33 Involute Spur Gear Tooth Correction : Part-I
  34. LECTURE 34 Involute Spur Gear Tooth Correction : Part-II
  35. LECTURE 35 Involute Spur Gear Tooth Correction : Part-III
  36. LECTURE 36 Involute Spur Gear Tooth Correction : Tutorial ( Workout Example)
  37. LECTURE 37 Involute Spur Gear Tooth Correction : Tutorial (Workout Example-2)
  38. LECTURE 38 Tooth Tip Interference, Avoidance and Contact Ratio in Involute Internal Gearing
  39. Lecture 39
  40. Lecture 40
  41. Lecture 41
  42. Lecture 42
  43. Lecture 43
  44. Lecture 44
  45. Live Session 27-03-2021
  46. Live Session 10-04-2021
  47. Live Session 04-05-2022
  48. Live Session 19-04-2022

From NPTEL (IITs and IISc) · CC BY-NC-SA. More from IIT Kharagpur.

Open Lecture Hall is free, with no ads and no sign-up. It is not run by or connected to any university; the lectures are the universities' own free recordings, played from where they host them. About & rights